Anping, Hebei · China's Wire Mesh Capital | APG Steel Grating — Direct Manufacturer of Hot-Dip Galvanized Steel Grating Instant QuoteSitemap

Steel Grating · Stair Treads · Covers

  • 20-Year Manufacturer
Industry News · Standard Interpretation

Steel Grating Standards & Technical Insights

Industry News · Technical Support · Product Cases

A veteran engineer with 30 years of experience explains the YB/T 4001.1 standard, sizing calculations and installation essentials, helping you purchase scientifically and avoid detours.

WhatsApp & E-mail support | Free sizing & quotation

  • Palletized hot-dip galvanized steel grating panels packed for shipment
  • Stacked hot-dip galvanized steel grating panels in factory yard
  • Double-tier galvanized steel grating stair treads with nosing
Contact Us

Steel Grating Factory

Address: East Industrial Park, Anping County
WhatsApp: +86 133 2318 8871
E-mail: [email protected]

Steel grating with common 30mm or 40mm bearing bar pitch

Published: 2020-01-03Popularity: 96

This article covers 40mm steel grating in three parts - steel grating specifications, hot-dip galvanized steel grating and basic concepts - with practical advice after each section. If you are comparing options or preparing a purchase, work through the points in order, cross-check the parts concerning galvanized bar grating against the same list, and adjust anything that conflicts with actual site conditions.

20190405095425777_272.jpg

      Steel grating has become the standard, preferred platform decking for all kinds of industrial platforms, typically used as walkway decking, platforms, trench covers and stair treads. In addition, compared with solid decking, its open grid structure maximizes the flow of light, air, liquids and sound, and greatly reduces wind load.

Steel Grating Specifications

Common specifications and corresponding parameters are summarized below; confirm each item before ordering:

A. Bearing bar: Q235 or stainless steel, available in plain flat, serrated anti-slip and I-section profiles, with common specs 20*5, 25*5, 30*3, 32*5, 40*5, 40*3, 50*5, 65*5, 100*8, 100*10 and so on.

B. Cross bar: same material as the bearing bar, using twisted square steel made by drawing wire rod through a square die and twisting it; common specs are 5*5, 6*6, 8*8 and so on.

C. From the above bearing bars and cross bars, the common steel grating specifications are 303/30/100, 325/30/100, 303/40/100, 323/40/100 and so on.

The above are common specifications; actual ordered dimensions and tolerance requirements shall be confirmed against the layout drawing.

The easiest things to miss when reading a specification table are tolerances and end treatment. 40mm steel grating usually has a machining allowance along its length; for recessed installation, state the edge banding and corner cutting requirements in advance. Galvanized bar grating is handled similarly in these details, so mark them all clearly on the drawing.

Hot-Dip Galvanized Steel Grating

Common materials and surface treatments are as follows:

ComponentMaterial and Specifications
Bearing Bar Pitch of Hot-Dip Galvanized Steel GratingBy series: Series 1 is 30mm; Series 2 is 40mm; Series 3 is 60mm.
Cross Bar Pitch of Hot-Dip Galvanized Steel GratingSeries 1 is 100mm and Series 2 is 50mm. Other specifications can be made to order.
Bearing Bars of Hot-Dip Galvanized Steel GratingMaterial is Q235A or stainless steel, in plain flat, serrated anti-slip and I-section profiles. Common specs are 20*5, 25*5, 25*3, 32*5, 30*5, 40*5, 40*3, 50*5, 65*5, 75*6, 100*8, 100*10 and so on.
Cross Bars of Hot-Dip Galvanized Steel GratingRound steel, twisted square steel, square steel or hexagonal steel in Q235A or 304 stainless steel. Twisted square steel is made by drawing wire rod through a square die and twisting it, with common specs 5*5, 6*6, 8*8mm and so on.

    Applications of hot-dip galvanized steel grating: used for platforms, walkways, trench covers, manhole covers, ladders, fences and handrails in petrochemical plants, power plants, waterworks, wastewater treatment plants, municipal works and sanitation projects.

Once material and surface treatment are decided, we recommend writing zinc coating thickness and appearance requirements into the technical agreement.

Actual parameters for the same model may vary slightly between manufacturers, so acceptance should be based on measured values. Spot-check the key dimensions of 40mm steel grating, especially on bulk deliveries. The corresponding parameters of galvanized bar grating can be verified the same way; report any deviation promptly.

Further reading: Selection points for galvanized grating and hot-dip galvanized steel grating

Besides what this article covers, galvanized grating is also common in actual projects. It shares similarities with this article's subject in structure and fabrication; for selection, check span, load and service environment in the same order. If both types of components are used in the same project, we recommend unifying material and surface treatment to avoid later galvanic corrosion or inconsistent appearance.

FAQ

What maintenance is required during daily use?

Maintenance mainly involves periodically checking whether fasteners are loose, whether touch-up paint has peeled off, and whether the panel surface shows obvious deformation or rust. Issues found should be dealt with promptly; overall maintenance is minimal.

How to choose between hot-dip galvanizing and cold galvanizing?

The two anti-corrosion mechanisms differ: hot-dip galvanizing immerses steel in molten zinc to form a metallurgically bonded coating, thick and long-lasting, suitable for outdoor and humid environments; cold galvanizing is electrochemical deposition with a thinner, more uniform appearance, suitable for dry indoor environments or applications requiring high dimensional precision.

What is most often overlooked during installation and acceptance?

First, bearing bars installed in the wrong direction reduce load capacity; second, insufficient fixing points or missing zinc touch-up paint; third, support beam spacing inconsistent with the layout drawing. These three items are most often overlooked on site.

The above is for sizing and construction reference. To verify specific parameters or request a quotation, please visitInstant Quote Page, or contact our technical staff.

Note that this article presents sizing approaches and general practice, and does not constitute a strength commitment for any specific project. For load-bearing safety-critical areas, the design drawings and on-site calculations shall prevail; contact our technical staff if in doubt.

How do you like this article?

0 0

Related Products