
Photovoltaic Steel Grating
- Bearing bars and cross bars are made of Q235 per GB/T 700; other materials can be used per user requirements.
- Bearing bars use hot-rolled flat bars or longitudinally slit hot-rolled or cold-rolled steel strips.
- Permissible deviations of flat bar dimensions comply with Table 1 of YB/T4001.1-2019.
- Serrated bearing bars use hot-rolled flat bars or longitudinally slit and toothed hot-rolled or cold-rolled steel strips. There must be no fewer than 5 teeth per 100mm.
- Cross-section dimensions and moment of inertia of I-shaped bearing bars.
The most common problem when purchasing photovoltaic steel grating is not price, but rework caused by specifications that do not match site conditions. This page lists the conditions to confirm in advance, practices for common working conditions, and key installation and acceptance points item by item, including those for PV steel grating, so they can be written into the technical agreement or purchase list.
Items to Confirm When Selecting Photovoltaic Steel Grating
This page does not list a fixed specification table, as such products are usually custom-fabricated to site conditions. We recommend confirming each item in the table above before inquiry: once mismatched with actual site conditions, refabrication is often required later.ProductsCommon specifications are organized by series for reference.
| Items to Confirm | What Needs to Be Clarified | Common Practices |
|---|---|---|
| Span and Support | Clear span between support beams and support surface width | Determine by field-measured dimensions |
| Service Load | Pedestrian, maintenance access or vehicle traffic | Verify by actual traffic type |
| Surface Treatment | Hot-dip galvanized, painted, or untreated | Hot-dip galvanizing recommended for outdoor and humid environments |
| Fixing Method | Welded fixing or special clips | Removable covers recommended for positions requiring maintenance |
| End Treatment | Whether banding or end plates are needed | Banding recommended for open edges |
| Packaging & Shipping | Whether packing and moisture protection are needed | Packing and cushioning recommended for long-distance shipping |
Photovoltaic Steel Grating Specifications
Different specifications correspond to different load capacities and theoretical weights. Common specification parameters of photovoltaic steel grating are shown in the table below; actual order dimensions and tolerance requirements are subject to confirmation against the layout drawing:
- Steel grating with a 30mm bearing bar pitch is the most widely used type in industry; among common steel grating series it offers the strongest resistance to surface impact.
- Steel grating with a 40mm bearing bar pitch is the most economical and lightweight type, and the ideal choice where spans are smallest.
- Steel grating with a 60mm bearing bar pitch and 50mm cross bar pitch was developed specifically for mining applications. It solves the problem of minerals splashing onto the panel surface, and is often specified for processing plants, transfer stations and crushing systems in the mining industry.
The above are common specifications; actual ordered dimensions and tolerance requirements shall be confirmed against the layout drawing.
Key Points for Selecting Photovoltaic Steel Grating
Confirm each item in the order below during selection to avoid most later rework. Record the conclusion of each step and submit it with your inquiry:
- Step 1 · Define Span and Support Conditions: First measure the clear span between support beams, then confirm the support surface width is sufficient; these two items determine the usable series range.
- Step 2 · Verify Service Load: Check separately for pedestrian, maintenance or vehicular traffic; maintenance and vehicular use differ greatly in bearing bar requirements.
- Step 3 · Determine Material and Surface Treatment: Ordinary carbon steel works for dry indoor environments; hot-dip galvanizing is recommended for outdoor or humid environments; chemical and coastal environments need separate confirmation.
- Step 4 · Confirm Shape and Fixing Method: Including whether cutouts, corner notches and banding are needed, and whether to use welded fixing or special clips.
Once the above conditions are confirmed, proceed to Instant Quote PageEstimate quantities by dimensions, or send the condition list to customer service for model recommendations from our technicians.
Typical Applications of Photovoltaic Steel Grating
Photovoltaic steel grating suits a wide range of working conditions, with typical applications including:
- Industrial Platforms & Maintenance Walkways: equipment platforms and inspection passages in power plants, chemical plants and steel-structure workshops;
- Municipal & Landscape: road drainage trench covers, rainwater grates, tree grates, park boardwalks;
- Transportation & Ports: wharf trestles, multi-story parking garage lanes, railway bridge walkways;
- Environmental & Water Treatment: walkways in wastewater treatment plants, tank platforms, screening machine platforms;
- Others: elevated tower platforms, stair treads, fences and railings, etc.
If your working conditions fall outside the above range, you can provide site photos and dimensions, and our technicians will help assess them.
Key Conditions to Confirm During Selection
- First clarify the span and support beam spacing to determine the required series;
- Then check load requirements by usage type (pedestrian, maintenance, vehicular);
- Finally, determine the surface treatment by service environment (dry indoor, outdoor, coastal, chemical).
Working Condition Comparison for Photovoltaic Steel Grating
The same specifications last very differently in different environments. The table below gives recommended practices by common service environment for your selection reference:
| Operating Environment | Recommended Practices | Note: |
|---|---|---|
| Indoor Dry Environments | Made of standard carbon steel with surface treatment as required | Focus on span and load; environmental impact is minimal |
| Humid or Water Treatment Environments | Use a higher corrosion protection grade with matching fasteners | Regularly inspect fixing points and surface corrosion |
| Vehicle Traffic Areas | Check load class against vehicle types | Note that bearing bars must run parallel to traffic direction |
| Pedestrian and Maintenance Walkways | Choose standard series, balancing walking comfort | Focus on surface flatness and end banding |
| High-Temperature or Large Temperature-Difference Environments | Select material and connection method by temperature | Watch for loosening caused by thermal expansion and contraction |
| Temporary or Short-Term Use | Can be configured with the light-duty series | For short schedules, prioritize easy disassembly and turnover |
Custom Fabrication & Quotation
For custom fabrication, we recommend stating tolerance ranges, zinc coating requirements and packaging in the contract or technical agreement for easy item-by-item acceptance. For batch projects, a sample can be made to confirm appearance and dimensions before mass production. For more specifications, visitProductsto view; for a quotation, go to Instant Quote Page for an estimate.
FAQ
Can it be custom-made to site dimensions?
Yes. Bearing bar specs, pitch, panel dimensions and banding forms can all be custom-made to drawings; cutouts, corner notches and shaped cutting are also supported. For bulk orders, a layout drawing can be confirmed before production.
What Are the Common Specifications of Photovoltaic Steel Grating?
Common specifications are determined by combinations of bearing bar width and thickness, bearing bar pitch, and cross bar pitch; different combinations correspond to different load capacities and theoretical weights. Our Products section lists common models by series; you can also send span and load requirements to customer service for sizing help.
Which surface treatment should I choose?
Hot-dip galvanizing is recommended for outdoor or humid environments; for dry indoor environments, untreated or painted is fine; coastal, chemical and other strongly corrosive environments need thicker zinc coatings or stainless steel, depending on the expected service life.
The above covers the common parameters and application scenarios of photovoltaic steel grating. Models vary considerably with span and load, so it is recommended toInstant Quote PageEnter actual dimensions for an estimate, or contact customer service to confirm the final selection.






