Anping, Hebei · China's Wire Mesh Capital | APG Steel Grating — Direct Manufacturer of Hot-Dip Galvanized Steel Grating Instant QuoteSitemap

Steel Grating · Stair Treads · Covers

  • 20-Year Manufacturer
Products · 8 Major Series

Full Range of Hot-Dip Galvanized Steel Grating in Stock

Steel Grating / Stair Treads / Trench Covers / Compound Grating - One-Stop Purchase

Full range of steel grating covering welded, press-locked, compound, serrated, I-type and more, with custom shaped fabrication and hot-dip galvanizing. In stock and ready to dispatch, with free sizing & quotation.

WhatsApp & E-mail support | Free sizing & quotation

  • Serrated hot-dip galvanized steel grating panel close-up
  • Plain hot-dip galvanized steel grating panel
  • Galvanized steel grating stair tread with checker plate nosing
You are here: Home > Products > Steel Grating

Compressed Steel Grating

Published: 2019-10-16Popularity: 162

20190405093204433_485.jpg

Compressed steel grating is made to order from drawings: overall dimensions, bearing bar size, pitches, edge banding and openings can all be set to site conditions. This page explains its construction and common specification forms, with selection advice for different service environments; for a size estimate, useInstant Quote Page.

Items to Confirm When Selecting Compressed Steel Grating

This page does not list a fixed specification table, as such products are usually custom-fabricated to site conditions. We recommend confirming each item in the table above before inquiry: once mismatched with actual site conditions, refabrication is often required later.ProductsCommon specifications are organized by series for reference.

Items to ConfirmWhat Needs to Be ClarifiedCommon Practices
Span and SupportClear span between support beams and support surface widthDetermine by field-measured dimensions
Service LoadPedestrian, maintenance access or vehicle trafficVerify by actual traffic type
DimensionsPanel length and width, whether openings or notches are neededCustom fabrication per layout drawing
End TreatmentWhether banding or end plates are neededBanding recommended for open edges
Acceptance RequirementsAcceptance Criteria for Flatness, Tolerances and AppearanceRecommended to specify in the technical agreement
Packaging & ShippingWhether packing and moisture protection are neededPacking and cushioning recommended for long-distance shipping

Press-Locked Steel Grating Panels

The following explains the key points of compressed steel grating from a practical application perspective:

 Compressed steel grating, also called press-locked steel grating, is made from ordinary low-carbon flat bars, stainless steel, brass plate or aluminium plate of set sizes through slotting (punching), interlocking, welding and finishing. It has firm weld points, uniform openings and an attractive, practical design. Press-locked grating combines the high strength, corrosion resistance and low maintenance of ordinary steel grating with uniform, precise assembly, a light and elegant structure, natural harmony and a refined style. It is both a functional product and a work of art, and is widely used.

360 Screenshot 20191016144005089.jpg

The above points can serve as a pre-purchase checklist; confirm each item before moving to the quotation stage.

Types of Press-Locked Steel Grating Panels

There are many kinds of compressed steel grating; the common classification is as follows:

  By different insertion methods and insertion angles, it can be divided into press-locked steel grating, heavy-duty steel grating, integral steel grating, sunshade steel grating, etc.

  u Press-locked type press-locked steel grating: after the bearing flat bars are slotted, the cross flat bars are press-locked into shape. Generally, the maximum fabrication height for ordinary type steel grating is 100mm; the grating length is usually under 2000mm.

  u Heavy-duty press-locked steel grating is a product where tall bearing bars and cross flat bars interlock and are pressed tight under 1200 tons of pressure. It is suitable for high-load, long-span applications.

  u Integral type press-locked steel grating: the bearing bars and cross flat bars have the same height, with slot depth equal to 1/2 of the bearing bar. Grating height does not exceed 100mm; length is usually under 2000mm.

  u Sunshade type press-locked steel grating: the bearing bars have 30° or 45° angled slots, and the cross bar flat bars are slotted and press-locked into shape. We can fabricate gratings with other pitches and specifications as needed, using ordinary carbon steel, stainless steel, aluminum and other materials. Grating height is under 100mm.

Determine the category first and then the specific model; this saves detours and makes comparison with other materials easier.

Press-Locked Steel Grating Specification and Weight Table

Specifications are the first thing checked during selection. The common models, pitch combinations and corresponding unit weights of compressed steel grating are listed below as a technical basis for purchasing and production planning:

360 Screenshot 20191016144535266.jpg

     Note:  1. Marking example: HG303/30 - HG" is the press-locked grating designation; 303 "303" is the flat bar section size [width x thickness] in mm; 30 "30" is the mesh pitch in mm.
           2. The nominal width is calculated for a flat bar thickness of 2mm; if the thickness is 5mm, add 3mm.
           3. Besides the pitches in the table on this page, press-locked steel grating with other pitches can be produced to user requirements.

The above are common specifications; actual ordered dimensions and tolerance requirements shall be confirmed against the layout drawing.

Key Points in Selecting Compressed Steel Grating

Confirm each item in the order below during selection to avoid most later rework. Record the conclusion of each step and submit it with your inquiry:

  • Step 1 · Balance Appearance vs. Load Capacity: Press-locked panels have a neat appearance and uniform hole spacing, suitable for appearance-critical platforms; load capacity must be checked by series.
  • Step 2 · Confirm Bearing Bar Specs and Pitch: Determined by span and load; the smaller the pitch, the denser the surface, with correspondingly higher self-weight and price.
  • Step 3 · Confirm Whether Banding Is Needed: Open edges should be banded, both to protect the panel and to prevent edges lifting and injuring people.
  • Step 4 · Confirm Installation and Maintenance Convenience: For areas needing frequent opening for maintenance, removable fixings rather than welding are recommended.

Once the above conditions are confirmed, proceed to Instant Quote PageEstimate quantities by dimensions, or send the condition list to customer service for model recommendations from our technicians.

Working Condition Comparison for Compressed Steel Grating

The same specifications last very differently in different environments. The table below gives recommended practices by common service environment for your selection reference:

Operating EnvironmentRecommended PracticesNote:
Indoor Dry EnvironmentsMade of standard carbon steel with surface treatment as requiredFocus on span and load; environmental impact is minimal
Outdoor and Open-Air EnvironmentsHot-dip galvanized surface treatment recommendedCheck zinc coating integrity and re-zinc cut edges
Humid or Water Treatment EnvironmentsUse a higher corrosion protection grade with matching fastenersRegularly inspect fixing points and surface corrosion
Chemical or Coastal EnvironmentsConfirm material and anti-corrosion scheme per mediumAvoid galvanic corrosion from direct contact between different metals
High-Temperature or Large Temperature-Difference EnvironmentsSelect material and connection method by temperatureWatch for loosening caused by thermal expansion and contraction
Clean Rooms and Food & PharmaceuticalPrioritize surface treatment and cleaning convenienceAvoid dust-collecting structures and cleaning dead corners

Custom Fabrication & Quotation

Before ordering, we recommend providing site photos, trench or platform dimensions and traffic requirements together, so we can give the model and layout plan in one go and reduce on-site cutting and rework. Common specifications are usually in stock; lead times for shaped parts and bulk orders depend on specification and quantity. For reference on similar projects, seeProject Cases; for a quotation, go directly to Instant Quote Page.

FAQ

How Is the Price of Compressed Steel Grating Calculated?

Usually calculated as the theoretical weight for the model times the material unit price, plus hot-dip galvanizing or other surface treatment costs, and fluctuating with steel and zinc prices. You canInstant Quote PageEnter specifications and dimensions for a quick estimate.

What Are the Common Specifications of Compressed Steel Grating?

Common specifications are determined by combinations of bearing bar width and thickness, bearing bar pitch, and cross bar pitch; different combinations correspond to different load capacities and theoretical weights. Our Products section lists common models by series; you can also send span and load requirements to customer service for sizing help.

Which surface treatment should I choose?

Hot-dip galvanizing is recommended for outdoor or humid environments; for dry indoor environments, untreated or painted is fine; coastal, chemical and other strongly corrosive environments need thicker zinc coatings or stainless steel, depending on the expected service life.

Once the specifications and surface treatment of compressed steel grating are confirmed, a quotation can be provided. For custom fabrication to drawings or load calculations, please contact us viaInstant Quote PageSubmit dimensions, or contact us directly for technical support.

Related News