Anping, Hebei · China's Wire Mesh Capital | APG Steel Grating — Direct Manufacturer of Hot-Dip Galvanized Steel Grating Instant QuoteSitemap

Steel Grating · Stair Treads · Covers

  • 20-Year Manufacturer
Products · 8 Major Series

Full Range of Hot-Dip Galvanized Steel Grating in Stock

Steel Grating / Stair Treads / Trench Covers / Compound Grating - One-Stop Purchase

Full range of steel grating covering welded, press-locked, compound, serrated, I-type and more, with custom shaped fabrication and hot-dip galvanizing. In stock and ready to dispatch, with free sizing & quotation.

WhatsApp & E-mail support | Free sizing & quotation

  • Serrated hot-dip galvanized steel grating panel close-up
  • Plain hot-dip galvanized steel grating panel
  • Galvanized steel grating stair tread with checker plate nosing

T1 Stair Tread

Published: 2019-10-16Popularity: 112

20190405162045996_419.jpg

Stairs are a high-risk location for accidents. When selecting T1 stair treads, besides load capacity, anti-slip performance and end fixing need particular attention. This page follows the order of 'dimensions - anti-slip - connection - accessories' and flags the data that should be counted in advance, so a single order can be placed.

Items to Confirm When Selecting T1 Stair Treads

This page does not list a fixed specification table, as such products are usually custom-fabricated to site conditions. We recommend confirming each item in the table above before inquiry: once mismatched with actual site conditions, refabrication is often required later.ProductsCommon specifications are organized by series for reference.

Items to ConfirmWhat Needs to Be ClarifiedCommon Practices
Stringer SpacingClear distance between the two stringersDetermines the load-bearing length of the tread
Tread DimensionsWidth and length, whether end plates are includedDetermine by actual stair dimensions
Connection MethodWelded to stringers or boltedDetermine by on-site construction conditions
Anti-Corrosion RequirementsIndoor or outdoor useHot-dip galvanizing recommended for outdoor and humid environments
Load RequirementsSingle-person traffic or multi-person/with goodsVerify by actual service conditions
End TreatmentWhether banding and anti-slip nosing are neededEnd banding and anti-slip nosing recommended

Stair Tread Types Explained

For easy comparison, T1 stair treads are listed below by the common classification methods, with the applicable conditions of each:

Stair treads, also called stair steps, steel stair plates or tread plates, are steel stairs used to connect platforms. By installation method and presence of nosing, they are divided into T1, T2, T3 and T4 types. T1 and T3 treads are welded directly to joists or channel steel without side plates - economical but not easy to dismantle; T1 has no nosing, T3 has a nosing (for anti-slip). T2 and T4 are bolted treads requiring 65*5mm side plates on both sides with two holes drilled; they can be dismantled and reused. T2 has no nosing, T4 has a nosing. Custom fabrication is available on request.

Determine the category first and then the specific model; this saves detours and makes comparison with other materials easier.

Stair Tread Models

Specifications are what get checked most often during selection. The common models, pitch combinations and corresponding unit weights of T1 stair treads are summarized below, and can serve as a technical basis for purchasing and production planning:

Standard stair treads: maximum length 1300mm, typically model 32*5 with 30mm mesh; minimum length 450mm, model 25*3 with 40mm mesh. Lengths between 450-1300mm are standard; width is determined by length - the longer the tread, the wider it is, and vice versa.

The above are common specifications; actual ordered dimensions and tolerance requirements shall be confirmed against the layout drawing.

Selection Points for T1 Stair Treads

Confirm each item in the order below during selection to avoid most later rework. Record the conclusion of each step and submit it with your inquiry:

  • Step 1 · Confirm Stair Stringer Spacing and Tread Width: The actual load-bearing length of the tread depends on stringer spacing; the width can be set per common traffic requirements.
  • Step 2 · Confirm Anti-Slip Requirements: For stairs with oil, standing water or outdoor exposure, serrated bearing bars or anti-slip raised surfaces are recommended.
  • Step 3 · Confirm End Connection Method: Including the welded or bolted connection form with stringers, and whether banding and end closure plates are needed.
  • Step 4 · Confirm Quantities and Accessories: Count by the actual number of steps, and check whether anti-slip nosings, side plates and fasteners are needed.

Once the above conditions are confirmed, proceed to Instant Quote PageEstimate quantities by dimensions, or send the condition list to customer service for model recommendations from our technicians.

Stair Tread Features and Uses

T1 stair treads are widely used in engineering mainly because they perform well overall in load capacity, drainage, corrosion protection and later maintenance. Compared with traditional solutions such as cast iron covers and checkered plate, their advantages lie mainly in the following aspects:

  • Stair treads are easy to install
  • Good ventilation, lighting, heat dissipation, explosion-proof and anti-slip performance
  • High strength, lightweight and durable stair treads
  • Durable with an attractive appearance and beautiful surface finish
  • Grating stair treads are very easy to maintain and resist dirt buildup.

Stair treads are widely used in power plants, waterworks and other factories, and in municipal and sanitation engineering - on platforms, walkways, visitor platforms, parking lots and other large venue floor surfaces.

20190405100202183_634.jpg

Overall, selection should weigh span, load and service environment together.

Welding Standards for Stair Treads

The standard sets out clear requirements for the material, dimensional tolerances and inspection methods of T1 stair treads; the key clauses are summarized below:

The banding of both side plates and each bearing bar uses single-side welding, with fillet welds of no less than 3mm.

We recommend checking each clause above during acceptance and keeping the factory inspection records.

Stair Tread Classification

T1 stair treads can be divided into the following categories by fabrication method and use; when selecting, determine the category first and then check the detailed parameters:

Determine the category first and then the specific model; this saves detours and makes comparison with other materials easier.

Anti-Slip Stair Treads

The points related to T1 stair treads are explained further below from a practical application perspective:

Raw material - serrated flat bars: the material is usually Q235. The difference between serrated and ordinary flat bars is the uneven teeth on one side of the bar (mainly for anti-slip; we mainly use longitudinally slit flat bars cut from steel plates).

Twisted square cross bar: also called twisted square bar, usually square bars of 5x5, 6x6, 8x8 twisted into rods.

The above points can serve as a pre-purchase checklist; confirm each item before moving to the quotation stage.

Features of Anti-Slip Stair Treads

timg (2).jpg

  • Made of flat bars serrated on one side, it has the features and uses of ordinary steel grating plus stronger anti-slip ability, especially suitable for wet, slippery places such as offshore oil platforms.
  • With hot-dip galvanized surface treatment, it has strong rust resistance and is maintenance- and replacement-free for 30 years. The product can be used as a trench cover hinged to the frame - theft-proof, safe and easy to open.
  • Made of high-strength carbon steel for very high strength: strength and toughness far exceed cast iron; suitable for docks, airports and other large-span, heavy-load environments.
  • Large mesh openings provide the best drainage: open area reaches 83.3%, making it the best choice for outdoor stairs.
  • Attractive appearance: clean lines, silver finish, modern look, economical material use, saving investment: lower in price than cast iron for large spans and heavy loads.

Stair Treads

Stair treads are a deeply processed product combining steel grating with anti-slip nosings and side plates. They are mainly used as steps on steel stairs, hence commonly called stair treads, or simply treads.

Stair tread specifications: Steel stair treads need to be made in various sizes to fit the corresponding stairs, but for economy and safety we recommend the following specifications:

T325/30/100 (for stair treads with width over 215mm and not over 305mm)

T255/30/100 ((for stair treads with width over 215mm and not over 305mm)

Steel Stair Treads

Also known as stair treads, they fall into two types by installation method: welded and bolted. Treads welded directly to the joists without added side plates are relatively economical and durable but hard to dismantle. Bolted treads need thicker side plates on both sides with holes drilled in them; they are fixed directly with bolts and can be reused after removal.

 WeSteel stair treads of various specifications can be custom-made to user needs; any type of steel grating can be made into various sizes to fit the corresponding stairs, but for economy we recommend using our recommended dimensions wherever possible.

Stair Tread Classification

timg (1).jpg

According to the presence or absence of a front guard plate and the connection to the stair stringers, grating stair treads are divided into four forms, denoted T1, T2, T3 and T4.

1. For economy, we recommend using modular widths wherever possible (Series 1: 125, 155, 185, 215, 245, 275; Series 2: 125, 165, 205, 245, 275mm, etc.) and lengths in multiples of 100mm (e.g. 500, 600, 700, 800, 900, 1000, 1200mm, etc.).

2. Stair tread tolerances: width W +/- 3mm, length L-3mm.

In addition, we offer stair treads with different anti-slip nosings, whose dimensions can be specified as needed. We generally recommend the following nosing dimensions.

Steel stair treads are fabricated from steel grating (steel grating is a steel product made by cross-arranging flat bars at set pitch with cross bars and welding them into a grid with square openings). The surface is usually hot-dip galvanized or electro-galvanized. Steel stair treads are mainly used for industrial platforms, stair treads, handrails, walkway floors, railway bridge walkways, elevated tower platforms, trench covers, manhole covers, road gratings and multi-story parking, and as fencing for institutions, schools, factories, enterprises, sports fields and garden villas; also for residential windows, balcony railings, and highway and railway fences. Stair treads are a deeply processed product combining steel grating with anti-slip nosings and side plates. They are mainly used as steps on steel stairs, hence commonly called stair treads, or simply treads.

Specifications: Steel stair treads need to be made in various sizes to fit the corresponding stairs, but for economy and safety we recommend the following specifications:

T325/30/100 (for stair treads with width over 215mm and not over 305mm)

T255/30/100 (for stair treads with width over 215mm and not over 305mm)

Types of Steel Stair Treads

(1) By installation, steel stair treads are divided into welded and bolted types. Welded treads are simply steel grating; bolted treads require 65X5mm flat bars added as side plates.

(2) By anti-slip requirements, steel stair treads are divided into those with nosings (checkered plate or strip steel) and those without. For safety reasons, we recommend treads with nosings.

T1 Stair Tread: Applicable Working Conditions

The same specifications last very differently in different environments. The table below gives recommended practices by common service environment for your selection reference:

Operating EnvironmentRecommended PracticesNote:
Outdoor and Open-Air EnvironmentsHot-dip galvanized surface treatment recommendedCheck zinc coating integrity and re-zinc cut edges
Humid or Water Treatment EnvironmentsUse a higher corrosion protection grade with matching fastenersRegularly inspect fixing points and surface corrosion
Chemical or Coastal EnvironmentsConfirm material and anti-corrosion scheme per mediumAvoid galvanic corrosion from direct contact between different metals
Pedestrian and Maintenance WalkwaysChoose standard series, balancing walking comfortFocus on surface flatness and end banding
High-Temperature or Large Temperature-Difference EnvironmentsSelect material and connection method by temperatureWatch for loosening caused by thermal expansion and contraction
Temporary or Short-Term UseCan be configured with the light-duty seriesFor short schedules, prioritize easy disassembly and turnover

Custom Fabrication & Quotation

T1 stair treads support made-to-drawing customization: overall dimensions, bearing bar size and pitch, banding type, openings and cut corners can all be processed to site conditions; for irregular parts and bulk orders, a layout drawing can be confirmed before production is scheduled. To estimate the quantity required, you canInstant Quote PageTry a size-based estimate; for model recommendations, browse ProductsCompare with similar specifications, then confirm with our service team.

FAQ

How Is the Price of T1 Stair Treads Calculated?

Usually calculated as the theoretical weight for the model times the material unit price, plus hot-dip galvanizing or other surface treatment costs, and fluctuating with steel and zinc prices. You canInstant Quote PageEnter specifications and dimensions for a quick estimate.

What Are the Common Specifications of T1 Stair Treads?

Common specifications are determined by combinations of bearing bar width and thickness, bearing bar pitch, and cross bar pitch; different combinations correspond to different load capacities and theoretical weights. Our Products section lists common models by series; you can also send span and load requirements to customer service for sizing help.

Which surface treatment should I choose?

Hot-dip galvanizing is recommended for outdoor or humid environments; for dry indoor environments, untreated or painted is fine; coastal, chemical and other strongly corrosive environments need thicker zinc coatings or stainless steel, depending on the expected service life.

Above are the main specifications and selection points for T1 stair treads. To determine a specific model based on on-site span and load, you canInstant Quote PageQuick estimation, or contact customer service directly for sizing advice and layout drawings.

Related News