Anping, Hebei · China's Wire Mesh Capital | APG Steel Grating — Direct Manufacturer of Hot-Dip Galvanized Steel Grating Instant QuoteSitemap

Steel Grating · Stair Treads · Covers

  • 20-Year Manufacturer
Industry News · Standard Interpretation

Steel Grating Standards & Technical Insights

Industry News · Technical Support · Product Cases

A veteran engineer with 30 years of experience explains the YB/T 4001.1 standard, sizing calculations and installation essentials, helping you purchase scientifically and avoid detours.

WhatsApp & E-mail support | Free sizing & quotation

  • Palletized hot-dip galvanized steel grating panels packed for shipment
  • Stacked hot-dip galvanized steel grating panels in factory yard
  • Double-tier galvanized steel grating stair treads with nosing
Contact Us

Steel Grating Factory

Address: East Industrial Park, Anping County
WhatsApp: +86 133 2318 8871
E-mail: [email protected]

Safety Requirements for Stair Grating Treads

Published: 2019-12-14Popularity: 172

Applying steel grating in actual projects is not complicated; the difficulty lies in matching specifications, material and service environment. This article explains in turn: Part 1, terms and definitions for grating treads; Part 2, structural requirements; and Part 5, general requirements. After reading it you will have a complete framework for judging steel stair treads.

201911062.jpg

1. Terms and Definitions for Grating Treads

Below we first briefly explain the relevant concepts and basic construction to make the following parameters and sizing content easier to understand.

1 Fixed steel inclined ladder

A tread steel ladder permanently installed on a building or equipment, inclined at 30°~75° to the horizontal (see Figure 1).

2 Stair Stringer (Frame) stile(rail)

The side members of a ladder used to mount treads or other transversely load-bearing components.

3 Tread tread(step)

The horizontal ladder component stepped on when going up and down, with a front-to-back depth of no less than 80 mm.

4 Tread height rise

The vertical distance between two adjacent treads.

5 Tread width going

The horizontal distance between the noses of two adjacent treads.

6 Clear width inside

The distance measured parallel to the treads between the inner sides of the two stringers, referred to as ladder width.

7 Ladder height

The vertical distance between the upper and lower datum planes of the stringer, referred to as ladder height.

8 Inclination angle of pitch

The angle between the plane containing the centerlines of the two stringers and the horizontal plane.

1 - tread;

2 - stringer;

3 - intermediate rail;

4 - post;

5 - handrail;

H - stair height;

L - stair span;

h1 - railing height;

h2 - handrail height;

α - ladder inclination angle;

r - tread rise;

g - tread width.

Once you grasp these basic concepts, the specifications and sizing recommendations that follow will be much easier to understand.

A practical tip for specification confirmation: write the bar size, bearing bar center pitch, cross bar pitch and overall dimensions together into the purchase list; specifying only one or two easily leads to mismatched deliveries. The specification labeling of steel grating is fully compared on the product page; number and check each panel against the layout drawing before ordering, and the same applies to steel stair treads.

2. Structural Requirements

The main standard clauses and acceptance requirements involved are as follows:

Stair Height

1 Ladder height should not exceed 5 m; above 5 m, an intermediate platform (rest platform) should be provided and the ladder divided into sections.

2 The ladder height of a single flight should not exceed 6 m, and the number of steps should not exceed 16.

        Clear Inside Width

1 For the clear width inside the ladder: the clear width for one-way traffic should be 600 mm; for frequent one-way and occasional two-way traffic, 800 mm; for frequent two-way traffic, 1000 mm.

2 The clear width inside the ladder shall be no less than 450 mm and should not exceed 1100 mm.

3. Stair Treads

1 The front-to-back depth of treads shall be no less than 80 mm; the overlap of adjacent treads in the front-to-back direction shall be no less than 10 mm and no more than 35 mm.

2 All treads within a flight shall be equally spaced; the tread spacing should be 225 mm~255 mm.

3 The top surface of the top tread shall be level with the platform surface, with no gap between the tread and the platform.

4 Treads shall use anti-slip materials or have anti-slip nosings at least 25 mm wide. Checkered steel plate no less than 4 mm thick, or anti-slip treated plain steel plate, or grating welded from 25 mm x 4 mm flat bars and small angle steel, or other equivalent structures, shall be used.

9. Stringers

Stringers shall have sufficient stiffness to keep lateral flexural deformation of the structure to a minimum, and shall project forward from the nose of the bottom tread by not less than 50 mm (see Figure 1).

X. Ladder Clearance Space

1 Above the ladder user, the vertical distance measured along the stringer centerline from the front edge of the tread nosing to the overhead obstruction shall be no less than 1200 mm.

2 Above the user of the inclined ladder, the vertical distance from the front edge of the tread nose to an overhead obstruction shall be not less than 2000 mm

4. Design Loads

1 The design load of a fixed steel inclined ladder shall be determined by actual service requirements but shall not be less than the values specified in this part.

2 A fixed steel inclined ladder shall withstand 5 times the specified live load standard value, and no less than a 4.4kN concentrated load applied at any point. The uniformly distributed live load standard value on the horizontal projection of the ladder shall be no less than 3.5kN/m2.

3 The concentrated live load at the midpoint of a tread shall be no less than 1.5kN, and the uniformly distributed load over the clear width inside the ladder no less than 2.2kN/m.

4 Ladder handrails shall withstand a concentrated load of no less than 890 N applied in any direction except vertically upward, with maximum deflection between adjacent posts no greater than 1/250 of the span. Intermediate rails shall withstand a horizontal concentrated load of no less than 700 N applied at the midpoint of their circumference, with maximum deflection no greater than 75 mm. End or terminal posts shall withstand a concentrated load of 890 N applied at the top of the post in any direction. These loads are not superimposed.

We recommend checking each clause above during acceptance and keeping the factory inspection records.

For the installation sequence, lay out first, then fix; avoid changing while laying. Once the layout drawing of steel grating is confirmed, avoid random cutting on site; if adjustment is really needed, the fixing and edging of steel grating stair treads should be adjusted accordingly to avoid leaving a loosening hazard.

5. General Requirements

The main standard clauses and acceptance requirements involved are as follows:

1 Material

The steel used for inclined steel ladders shall have mechanical properties not lower than Q235-B, with guaranteed carbon content.

2 Inclination of Steel Stairway

  1 The inclination of a fixed steel inclined ladder to the horizontal shall be within 30°~75°, preferably 30°~35°. The maximum inclination for occasional access should be 42°; for frequent two-way traffic, 38°.

  2 Within a flight, the combination of riser height and going shall remain consistent and shall meet the requirement of Equation (1):

550≤g+2r≤700....................................................(1)

Where:

g - tread width, in millimeters (mm);

r - tread rise, in millimeters (mm).

3 For examples of common ladder inclinations and the corresponding riser height r and going g combinations (g+2r=600), see Table 1; other inclinations may be determined by linear interpolation.

4 For examples of common ladder inclinations and height-to-span ratios (H:L), see Table 2.

We recommend checking each clause above during acceptance and keeping the factory inspection records.

For material selection, do not simply chase high grades. The material of steel grating should match the load requirements and service environment; over-specifying causes unnecessary cost increases. The corresponding treatment for steel stair treads can be found on the product page, chosen against actual conditions.

6. Rust and Corrosion Protection

Common materials and surface treatments are as follows:

1 Fixed steel inclined ladders shall be designed to minimize trapped moisture to reduce rusting and corrosion.

2 According to the ladder's service occasion and environmental conditions, suitable anti-rust and anti-corrosion coating shall be applied.

3 After installation, the inclined steel ladder shall be given at least one coat of primer and one (or more) topcoat(s), or an equivalent anti-rust, anti-corrosion coating.

7. Grounding

For lightning protection of outdoor inclined steel ladders and their connections, connection and grounding accessories shall comply with GB 50057.

Once material and surface treatment are decided, we recommend writing zinc coating thickness and appearance requirements into the technical agreement.

Regarding corrosion protection, one point is easily overlooked: cutting and welding at the installation site will damage the original coating, and these areas need zinc repair after construction, otherwise rust will easily start from the cuts. Steel stair treads have the same problem; it is best to write this into the technical requirements at the construction briefing.

8. Fabrication and Installation

On-site construction generally follows the steps and technical requirements below; complete the technical disclosure before starting work:

1 Inclined steel ladders shall use welded connections; welding shall comply with GB 50205. Where other connection methods are used, connection strength shall be no lower than welding. Installed ladders shall be free of skew, twist, deformation and other defects.

2 Manufacturing and installation processes shall ensure the ladder and all its components have smooth surfaces, free of sharp edges, corners, burrs or other external defects that could injure users or hinder passage.

3 Where an inclined steel ladder connects to a platform beam attached to equipment, bolted connections with slotted holes are preferred at the joint.

After installation, check each panel's fixing points and flatness; put into use only after confirming no warping or looseness.

For the installation sequence, lay out first, then fix; avoid changing while laying. Once the layout drawing of steel grating is confirmed, avoid random cutting on site; if adjustment is really needed, the fixing and edging of steel stair treads should be adjusted accordingly to avoid leaving a loosening hazard.

Related Reading: Selection Reference for Steel Stair Treads and Steel Grating Stair Treads

Besides the content introduced in this article, actual projects often also involve steel stair treads. They share similarities with the topic of this article in structural form and processing methods; when selecting, just check span, load, and service environment in turn. If both types of components are used together in the same project, unify the material and surface treatment to avoid galvanic corrosion or inconsistent appearance later.

FAQ

What is most often overlooked during installation and acceptance?

First, bearing bars installed in the wrong direction reduce load capacity; second, insufficient fixing points or missing zinc touch-up paint; third, support beam spacing inconsistent with the layout drawing. These three items are most often overlooked on site.

What information is needed for custom sizes?

Usually you need to provide the panel dimensions (length x width), bearing bar specs and direction, center-to-center pitch of bearing bars and cross bars, surface treatment, and special requirements such as cutouts, corner notches and banding. Site photos or sketches are even better.

Why do different manufacturers quote different weights for the same specifications?

The main difference lies in the actual measured thickness and tolerance control of the bearing bars. When bars are supplied at the lower tolerance limit, weight per unit area falls below the theoretical value, and load capacity drops accordingly. We recommend specifying thickness tolerance clearly when purchasing.

The above is for sizing and construction reference. To verify specific parameters or request a quotation, please visitInstant Quote Page, or contact our technical staff.

Note that this article presents sizing approaches and general practice, and does not constitute a strength commitment for any specific project. For load-bearing safety-critical areas, the design drawings and on-site calculations shall prevail; contact our technical staff if in doubt.

How do you like this article?

0 0

Related Products