
T3 stair treads are used as the stepping surface of steel stairs and maintenance stairways, with anti-slip performance, firmness and dimensional fit as the core requirements. This page explains stringer spacing, anti-slip form, end connection and quantity take-off item by item, and gives recommendations for different service environments. The same approach applies to stair treads.
Items to Confirm When Selecting T3 Stair Treads
This page does not list a fixed specification table, as such products are usually custom-fabricated to site conditions. We recommend confirming each item in the table above before inquiry: once mismatched with actual site conditions, refabrication is often required later.ProductsCommon specifications are organized by series for reference.
| Items to Confirm | What Needs to Be Clarified | Common Practices |
|---|---|---|
| Stringer Spacing | Clear distance between the two stringers | Determines the load-bearing length of the tread |
| Tread Dimensions | Width and length, whether end plates are included | Determine by actual stair dimensions |
| Anti-Slip Type | Serrated bearing bars or anti-slip raised patterns | Required for oily, wet or outdoor environments |
| Connection Method | Welded to stringers or bolted | Determine by on-site construction conditions |
| Quantity Summary | Number of steps and matching side plates | Count by actual number of steps and reserve spares |
| Anti-Corrosion Requirements | Indoor or outdoor use | Hot-dip galvanizing recommended for outdoor and humid environments |
Stair Tread Types Explained
T3 stair treads come in many types. The common classification methods are as follows:
Stair treads, also called stair steps, steel stair plates or tread plates, are steel stairs used to connect platforms. By installation method and presence of nosing, they are divided into T1, T2, T3 and T4 types. T1 and T3 treads are welded directly to joists or channel steel without side plates - economical but not easy to dismantle; T1 has no nosing, T3 has a nosing (for anti-slip). T2 and T4 are bolted treads requiring 65*5mm side plates on both sides with two holes drilled; they can be dismantled and reused. T2 has no nosing, T4 has a nosing. Custom fabrication is available on request.

Determine the category first and then the specific model; this saves detours and makes comparison with other materials easier.
Stair Tread Models
The most frequently checked item in selection is the specification. The common models, pitch combinations and corresponding unit weights of T3 stair treads are listed below as a technical basis for purchasing and production planning:
Standard stair treads: maximum length 1300mm, typically model 32*5 with 30mm mesh; minimum length 450mm, model 25*3 with 40mm mesh. Lengths between 450-1300mm are standard; width is determined by length - the longer the tread, the wider it is, and vice versa.
The above are common specifications; actual ordered dimensions and tolerance requirements shall be confirmed against the layout drawing.
Key Points for Selecting T3 Stair Treads
Confirm each item in the order below during selection to avoid most later rework. Record the conclusion of each step and submit it with your inquiry:
- Step 1 · Confirm Stair Stringer Spacing and Tread Width: The actual load-bearing length of the tread depends on stringer spacing; the width can be set per common traffic requirements.
- Step 2 · Confirm Anti-Slip Requirements: For stairs with oil, standing water or outdoor exposure, serrated bearing bars or anti-slip raised surfaces are recommended.
- Step 3 · Confirm End Connection Method: Including the welded or bolted connection form with stringers, and whether banding and end closure plates are needed.
- Step 4 · Confirm Quantities and Accessories: Count by the actual number of steps, and check whether anti-slip nosings, side plates and fasteners are needed.
Once the above conditions are confirmed, proceed to Instant Quote PageEstimate quantities by dimensions, or send the condition list to customer service for model recommendations from our technicians.
Stair Tread Features and Uses
The main performance features of T3 stair treads can be summarized as follows, for checking item by item during option comparison and technical briefings:
- Stair treads are easy to install
- Good ventilation, lighting, heat dissipation, explosion-proof and anti-slip performance
- High strength, lightweight and durable stair treads
- Durable with an attractive appearance and beautiful surface finish
- Grating stair treads are very easy to maintain and resist dirt buildup.
Stair treads are widely used in power plants, waterworks and other factories, and in municipal and sanitation engineering - on platforms, walkways, visitor platforms, parking lots and other large venue floor surfaces.
Overall, selection should weigh span, load and service environment together.
Welding Standards for Stair Treads
Regarding the standard requirements and inspection items for T3 stair treads, the following are most often checked at incoming acceptance:
The banding of both side plates and each bearing bar uses single-side welding, with fillet welds of no less than 3mm.
We recommend checking each clause above during acceptance and keeping the factory inspection records.
Stair Tread Classification
For easy comparison, T3 stair treads are listed below one by one by common classification, with their respective applications:
Determine the category first and then the specific model; this saves detours and makes comparison with other materials easier.
Anti-Slip Stair Treads
Regarding T3 stair treads, the following points are most often asked about in purchasing and use, and most need to be confirmed in advance:
Raw material - serrated flat bars: the material is usually Q235. The difference between serrated and ordinary flat bars is the uneven teeth on one side of the bar (mainly for anti-slip; we mainly use longitudinally slit flat bars cut from steel plates).
Twisted square cross bar: also called twisted square bar, usually square bars of 5x5, 6x6, 8x8 twisted into rods.
The above points can serve as a pre-purchase checklist; confirm each item before moving to the quotation stage.
Features of Anti-Slip Stair Treads
- Made of flat bars serrated on one side, it has the features and uses of ordinary steel grating plus stronger anti-slip ability, especially suitable for wet, slippery places such as offshore oil platforms.
- With hot-dip galvanized surface treatment, it has strong rust resistance and is maintenance- and replacement-free for 30 years. The product can be used as a trench cover hinged to the frame - theft-proof, safe and easy to open.
- Made of high-strength carbon steel for very high strength: strength and toughness far exceed cast iron; suitable for docks, airports and other large-span, heavy-load environments.
- Large mesh openings provide the best drainage: open area reaches 83.3%, making it the best choice for outdoor stairs.
- Attractive appearance: clean lines, silver finish, modern look, economical material use, saving investment: lower in price than cast iron for large spans and heavy loads.
Stair Treads
Stair treads are a deeply processed product combining steel grating with anti-slip nosings and side plates. They are mainly used as steps on steel stairs, hence commonly called stair treads, or simply treads.
Stair tread specifications: Steel stair treads need to be made in various sizes to fit the corresponding stairs, but for economy and safety we recommend the following specifications:
T325/30/100 (for stair treads with width over 215mm and not over 305mm)
T255/30/100 ((for stair treads with width over 215mm and not over 305mm)
Steel Stair Treads

Also known as stair treads, they fall into two types by installation method: welded and bolted. Treads welded directly to the joists without added side plates are relatively economical and durable but hard to dismantle. Bolted treads need thicker side plates on both sides with holes drilled in them; they are fixed directly with bolts and can be reused after removal.
Steel stair treads of various specifications can be custom-made to user needs; any type of steel grating can be made into various sizes to fit the corresponding stairs, but for economy we recommend using our recommended dimensions wherever possible.
Our steel stair treads come in four forms, T1, T2, T3 and T4, classified by presence of nosing and connection to stringers.
1. For economy, we recommend using modular widths wherever possible (Series 1: 125, 155, 185, 215, 245, 275; Series 2: 125, 165, 205, 245, 275mm, etc.) and lengths in multiples of 100mm (e.g. 500, 600, 700, 800, 900, 1000, 1200mm, etc.).
2. Stair Tread Tolerances: Width W±3mm, Length L-3mm.
In addition, we offer stair treads with different anti-slip nosings, whose dimensions can be specified as needed. We generally recommend the following nosing dimensions.
Steel stair treads are fabricated from steel grating (steel grating is a steel product made by cross-arranging flat bars at set pitch with cross bars and welding them into a grid with square openings). The surface is usually hot-dip galvanized or electro-galvanized. Steel stair treads are mainly used for industrial platforms, stair treads, handrails, walkway floors, railway bridge walkways, elevated tower platforms, trench covers, manhole covers, road gratings and multi-story parking, and as fencing for institutions, schools, factories, enterprises, sports fields and garden villas; also for residential windows, balcony railings, and highway and railway fences. Stair treads are a deeply processed product combining steel grating with anti-slip nosings and side plates. They are mainly used as steps on steel stairs, hence commonly called stair treads, or simply treads.
Specifications: Steel stair treads need to be made in various sizes to fit the corresponding stairs, but for economy and safety we recommend the following specifications:
T325/30/100 (for stair treads with width over 215mm and not over 305mm)
T255/30/100 (for stair treads with width over 215mm and not over 305mm)
Types of Steel Stair Treads
(1) By installation, steel stair treads are divided into welded and bolted types. Welded treads are simply steel grating; bolted treads require 65X5mm flat bars added as side plates.
(2) By anti-slip requirements, steel stair treads are divided into those with nosings (checkered plate or strip steel) and those without. For safety reasons, we recommend treads with nosings.
T3 Stair Tread Application Conditions Comparison
The same specifications last very differently in different environments. The table below gives recommended practices by common service environment for your selection reference:
| Operating Environment | Recommended Practices | Note: |
|---|---|---|
| Outdoor and Open-Air Environments | Hot-dip galvanized surface treatment recommended | Check zinc coating integrity and re-zinc cut edges |
| Humid or Water Treatment Environments | Use a higher corrosion protection grade with matching fasteners | Regularly inspect fixing points and surface corrosion |
| Vehicle Traffic Areas | Check load class against vehicle types | Note that bearing bars must run parallel to traffic direction |
| Pedestrian and Maintenance Walkways | Choose standard series, balancing walking comfort | Focus on surface flatness and end banding |
| High-Temperature or Large Temperature-Difference Environments | Select material and connection method by temperature | Watch for loosening caused by thermal expansion and contraction |
| Clean Rooms and Food & Pharmaceutical | Prioritize surface treatment and cleaning convenience | Avoid dust-collecting structures and cleaning dead corners |
Custom Fabrication & Quotation
T3 stair treads support made-to-drawing customization: overall dimensions, bearing bar size and pitch, edging form, openings and cut corners can all be fabricated to site conditions; for shaped parts and bulk orders, a layout drawing can be confirmed before production is scheduled. To estimate quantities, please useInstant Quote PageTry a size-based estimate; for model recommendations, browse ProductsCompare with similar specifications, then confirm with our service team.
FAQ
What mistakes are easy to make during installation?
Three main points: first, bearing bars installed in the wrong direction so loads are carried by cross bars; second, insufficient or missing fixing points; third, welding slag not removed and zinc-rich paint not reapplied after welding. These three cause the most on-site problems.
Can it be custom-made to site dimensions?
Yes. Bearing bar specs, pitch, panel dimensions and banding forms can all be custom-made to drawings; cutouts, corner notches and shaped cutting are also supported. For bulk orders, a layout drawing can be confirmed before production.
What Are the Common Specifications of T3 Stair Treads?
Common specifications are determined by combinations of bearing bar width and thickness, bearing bar pitch, and cross bar pitch; different combinations correspond to different load capacities and theoretical weights. Our Products section lists common models by series; you can also send span and load requirements to customer service for sizing help.
Once the specifications and surface treatment of T3 stair treads are confirmed, a quotation can be provided. For made-to-drawing customization or load calculation, please contact us viaInstant Quote PageSubmit dimensions, or contact us directly for technical support.






