This article explains steel grating step by step, in the order of model code interpretation, typical applications and basic concepts, offering practical decision rules rather than theory alone. If you have drawings or on-site dimensions at hand, check them against the points listed here; drainage trench covers can follow the same sequence.
Interpreting Steel Grating Specifications and Models
Common specifications and corresponding parameters are summarized below; confirm each item before ordering:
Take G323/30/100, the most typical model code in the steel grating industry, as an example:

- In G323/30/100, the leading G indicates that this string of data is a steel grating model code; if it is SG, the grating is serrated steel grating, with identical tooth grooves evenly distributed along the bearing bars.
- In G323/30/100, the first two digits 32 of 323 indicate that the bearing bar width is 32mm, and the following 3 indicates that the bearing bar thickness is 3mm.
- In G323/30/100, the middle 32 indicates that the bearing bar pitch is 32mm.
- In G323/30/100, the final number 100 indicates that the cross bar pitch (cross bars are also called twisted square bars) in the steel grating diagram above is 100mm.
- The cross bar diameter is generally not shown in the model code; the common cross bar diameters are 6mm or 8mm.
The above are common specifications; actual ordered dimensions and tolerance requirements shall be confirmed against the layout drawing.
Bigger is not always better. Steel grating selection should be as economical as possible while meeting load requirements; over-thickening increases self-weight and cost and complicates installation. The product page offers a fuller comparison for hot-dip galvanized trench covers; refer to it before deciding.
Typical Applications
Main applications are as follows:
- Industrial Platforms & Maintenance Walkways: equipment platforms and inspection passages in power plants, chemical plants and steel-structure workshops;
- Municipal & Landscape: road drainage trench covers, rainwater grates, tree grates, park boardwalks;
- Transportation & Ports: wharf trestles, multi-story parking garage lanes, railway bridge walkways;
- Environmental & Water Treatment: walkways in wastewater treatment plants, tank platforms, screening machine platforms;
- Others: elevated tower platforms, stair treads, fences and railings, etc.
If your working conditions fall outside the above range, you can provide site photos and dimensions, and our technicians will help assess them.
Requirements often differ between areas of the same site. With steel grating, for example, main walkways and corner zones, or frequently used areas and occasional maintenance areas, can take different specifications. Mixing hot-dip galvanized trench covers should also be planned by zone, balancing safety and cost.
Key Conditions to Confirm During Selection
- First clarify the span and support beam spacing to determine the required series;
- Then check load requirements by usage type (pedestrian, maintenance, vehicular);
- Finally, determine the surface treatment by service environment (dry indoor, outdoor, coastal, chemical).
A practical tip for specification confirmation: write bearing bar specs, bearing bar pitch, cross bar pitch and overall dimensions into the purchase list at the same time; specifying only one or two often leads to mismatched deliveries. The specification marking system is fully cross-referenced on the product page; number and check each panel against the layout drawing before ordering. The same applies to hot-dip galvanized trench covers.
Further reading: Sizing reference for drainage trench covers and hot-dip galvanized trench covers
If a project uses both drainage trench covers and hot-dip galvanized trench covers, plan them together on a single layout drawing. This lets edge trimming, fixing and openings at the interfaces be handled uniformly, avoids dimension conflicts during on-site installation, and makes later maintenance easier.
- For all product specifications and theoretical weights by series, visit Steel Grating Product Center
- To estimate cost by size and quantity, use Instant Quote PageSubmit Requirements
- To see how similar projects were executed, refer to Project Cases field applications
FAQ
Why do different manufacturers quote different weights for the same specifications?
The main difference lies in the actual measured thickness and tolerance control of the bearing bars. When bars are supplied at the lower tolerance limit, weight per unit area falls below the theoretical value, and load capacity drops accordingly. We recommend specifying thickness tolerance clearly when purchasing.
What information is needed for custom sizes?
Usually you need to provide the panel dimensions (length x width), bearing bar specs and direction, center-to-center pitch of bearing bars and cross bars, surface treatment, and special requirements such as cutouts, corner notches and banding. Site photos or sketches are even better.
How to choose between hot-dip galvanizing and cold galvanizing?
The two anti-corrosion mechanisms differ: hot-dip galvanizing immerses steel in molten zinc to form a metallurgically bonded coating, thick and long-lasting, suitable for outdoor and humid environments; cold galvanizing is electrochemical deposition with a thinner, more uniform appearance, suitable for dry indoor environments or applications requiring high dimensional precision.
The above is for sizing and construction reference. To verify specific parameters or request a quotation, please visitInstant Quote Page, or contact our technical staff.
The above is general guidance. For a specific project, we still recommend submitting span, load class and service environment to our technicians for review. Steel grating is a load-bearing component; rework caused by wrong specification choices costs far more than the time spent on upfront calculation.






