Anping, Hebei · China's Wire Mesh Capital | APG Steel Grating — Direct Manufacturer of Hot-Dip Galvanized Steel Grating Instant QuoteSitemap

Steel Grating · Stair Treads · Covers

  • 20-Year Manufacturer
Products · 8 Major Series

Full Range of Hot-Dip Galvanized Steel Grating in Stock

Steel Grating / Stair Treads / Trench Covers / Compound Grating - One-Stop Purchase

Full range of steel grating covering welded, press-locked, compound, serrated, I-type and more, with custom shaped fabrication and hot-dip galvanizing. In stock and ready to dispatch, with free sizing & quotation.

WhatsApp & E-mail support | Free sizing & quotation

  • Serrated hot-dip galvanized steel grating panel close-up
  • Plain hot-dip galvanized steel grating panel
  • Galvanized steel grating stair tread with checker plate nosing
You are here: Home > Products > Steel Grating

Platform Steel Grating

Published: 2019-10-15Popularity: 173

Platform steel grating is a panel-shaped steel product made by cross-arranging flat bars at certain pitches with cross bars and press-welding them into panels with square mesh openings, with a hot-dip galvanized surface. It is the most widely used panel type in industrial platforms, walkways, and trestles. It has strong resistance to surface impact, and the materials, pitches, and edge banding of flat bars and cross bars all have explicit standard requirements. This article explains, in selection order, how to choose the bearing bar pitch and the mandatory rules for edge banding welding, for reference during procurement.

Hot-dip galvanized platform steel grating walkway on trestle
Hot-dip galvanized platform steel grating walkway on trestle

Platform steel grating is a product that can be custom-fabricated from drawings: overall dimensions, flat bar specifications, pitch, edge banding, and openings can all be determined according to site conditions. This page explains its composition and common specification forms, and gives selection suggestions for different service environments; for estimation by dimensions, you can directly use theInstant Quote Page.

Items to confirm when selecting platform steel grating

This page does not list a fixed specification table, as such products are usually custom-fabricated to site conditions. We recommend confirming each item in the table above before inquiry: once mismatched with actual site conditions, refabrication is often required later.ProductsCommon specifications are organized by series for reference.

Items to ConfirmWhat Needs to Be ClarifiedCommon Practices
Span and SupportClear span between support beams and support surface widthDetermine by field-measured dimensions
Service LoadPedestrian, maintenance access or vehicle trafficVerify by actual traffic type
Material RequirementsCarbon steel or stainless steel, grade requirementsDetermine by corrosion grade of service environment
Surface TreatmentHot-dip galvanized, painted, or untreatedHot-dip galvanizing recommended for outdoor and humid environments
DimensionsPanel length and width, whether openings or notches are neededCustom fabrication per layout drawing
Fixing MethodWelded fixing or special clipsRemovable covers recommended for positions requiring maintenance

1. How to choose the bearing bar pitch: 30 / 40 / 60mm

The flat bar center pitch directly determines panel strength, weight, and price, and is the primary factor in selection. The applicable scenarios of the three common pitches are compared below:

Bearing bar center pitchFeaturesApplication Scenarios
30mmThe most widely used type in industry, with the strongest resistance to surface impactPlatforms subject to impact and heavy loads; equipment maintenance platforms
40mmThe most economical and lightest typeThe ideal choice for occasions with smaller spans
60mm (cross bar pitch 50mm)A type developed specifically for mining applications, solving the problem of mineral spillage on the panel surfacePanel surfaces of mining processing plants, transfer stations, and crushing systems
Structural diagram of 30mm and 40mm bearing bar center pitch
Structural diagram of 30mm and 40mm bearing bar center pitch

In addition, the center pitch of cross bars is usually available in 50mm and 100mm, which can be selected in combination according to usage requirements.

2. Classification by welding method and flat bar shape

  • By welding method: press-welded, press-locked, lock-crimped, and swaged-lock platform steel gratings;
  • By side surface shape of load-bearing flat bars: flat type, serrated type, I-section type, etc.;
  • By use: steel gratings for general purposes and steel gratings for special purposes (such as trench covers and stair treads).
Equipment platform steel grating installation and handrail
Equipment platform steel grating installation

3. Material standards

  • Flat bars and cross bars are made of Q235 per GB/T700, and other materials may be used upon user request;
  • Flat bars use hot-rolled flat bars or longitudinally slit hot-rolled or cold-rolled steel strips;
  • Dimensional tolerances of flat bars comply with Table 1 of YB/T4001.1-2007;
  • Serrated flat bars use hot-rolled flat bars or longitudinally slit, toothed hot-rolled/cold-rolled steel strips, with no fewer than 5 serrations per 100mm;
  • The cross-section dimensions and moment of inertia of I-section flat bars follow the standard.
Finished hot-dip galvanized platform steel grating in stock
Finished hot-dip galvanized platform steel grating

4. Welding standards for edge banding and accessories

  • Kick plates (curb plates), checkered plate guards, installation connectors, and other accessories may be welded around the perimeter;
  • Edge banding may use flat bars of different specifications from the load-bearing flat bars, or angle steel, channel steel, square tubes, etc.;
  • On platforms that need to be moved or opened frequently, handles and hinges may be installed;
  • Edge banding welding standard: for Series 1, one weld per five bars; for Series 2, one weld per four bars; for Series 3, one weld per three bars; the weld is a single-side fillet weld of no less than 3mm, with a weld length of 20mm.

Selection key points for platform steel grating

Confirm each item in the order below during selection to avoid most later rework. Record the conclusion of each step and submit it with your inquiry:

  • Step 1 · Define Span and Support Conditions: First measure the clear span between support beams, then confirm the support surface width is sufficient; these two items determine the usable series range.
  • Step 2 · Verify Service Load: Check separately for pedestrian, maintenance or vehicular traffic; maintenance and vehicular use differ greatly in bearing bar requirements.
  • Step 3 · Determine Material and Surface Treatment: Ordinary carbon steel works for dry indoor environments; hot-dip galvanizing is recommended for outdoor or humid environments; chemical and coastal environments need separate confirmation.
  • Step 4 · Confirm Shape and Fixing Method: Including whether cutouts, corner notches and banding are needed, and whether to use welded fixing or special clips.

Once the above conditions are confirmed, proceed to Instant Quote PageEstimate quantities by dimensions, or send the condition list to customer service for model recommendations from our technicians.

5. Typical application scenarios

Platform steel gratings are widely used in chemical, power, water supply, sewage treatment, port and dock, construction, shipbuilding, self-service parking, municipal engineering, environmental sanitation engineering, and other fields, serving as platforms, walkways, trestles, trench covers, manhole covers, ladders, fences, etc. They are easy to install and a mature industrial panel product.

Industrial platform steel grating installation example
Industrial platform steel grating installation example

Working condition comparison for platform steel grating

The same specifications last very differently in different environments. The table below gives recommended practices by common service environment for your selection reference:

Operating EnvironmentRecommended PracticesNote:
Indoor Dry EnvironmentsMade of standard carbon steel with surface treatment as requiredFocus on span and load; environmental impact is minimal
Humid or Water Treatment EnvironmentsUse a higher corrosion protection grade with matching fastenersRegularly inspect fixing points and surface corrosion
Chemical or Coastal EnvironmentsConfirm material and anti-corrosion scheme per mediumAvoid galvanic corrosion from direct contact between different metals
Vehicle Traffic AreasCheck load class against vehicle typesNote that bearing bars must run parallel to traffic direction
Clean Rooms and Food & PharmaceuticalPrioritize surface treatment and cleaning convenienceAvoid dust-collecting structures and cleaning dead corners
Temporary or Short-Term UseCan be configured with the light-duty seriesFor short schedules, prioritize easy disassembly and turnover

Custom Fabrication & Quotation

Common specifications are usually in stock; lead times for shaped parts and bulk orders are determined by specification and production scheduling. For projects needing site measurement and layout design, provide photos and dimensions and we will assist with drawings to reduce on-site cutting. For practices on similar projects, seeProject Cases, for model comparison see Products.

6. FAQs

How long does platform steel grating last?

The service life mainly depends on the galvanized coating thickness and the corrosion level of the service environment: 40-50 years in dry inland/indoor environments, about 20-30 years in ordinary outdoor atmospheres, about 10-15 years in humid coastal conditions, and about 5-10 years in chemical acid-alkali environments. For detailed data, see"How Long Does Hot-Dip Galvanized Steel Grating Last".

Does the flat bar direction matter during installation?

Yes. The flat bars must run along the span direction of the panel with both ends resting on the supporting beams; installing them backwards transfers the load to the cross bars and greatly reduces the load capacity. For on-site identification, see"Correct Installation Method for Steel Grating Flat Bar Direction".

How to estimate price and weight?

Platform steel grating is priced by the theoretical weight corresponding to the specification model. You canInstant Quote Pageenter the flat bar specifications and panel dimensions for a quick estimate, or send the span, load, and trench dimensions to customer service for a selection calculation.

If you need to determine the specific model based on site span and load, feel free toconsult us online; we can provide layout drawings and selection suggestions.

Related News