About Type I steel grating, this article explains, in the order of what steel grating is, its main advantages, and its specification parameters, item by item, giving directly executable judgment methods rather than only principles. Those with drawings or site dimensions can check the key points one by one; drainage trench covers can follow the same judgment order.
What Is Steel Grating
This section first clarifies the basic concepts, structural forms and common names, laying the groundwork for what follows.

Steel grating is a steel structural member formed by pressure-welding bearing flat bars and structural cross bars together in a certain regular arrangement, widely used in metallurgy, petrochemicals, transportation, light industry, municipal and environmental protection fields, generally used to make metal structural members such as platforms, floors, trench covers, treads, fences and water supply and drainage works. In July 2007, China issued the new industry standard YB/T4001.1-2007 for steel grating, enabling rapid development of steel grating production and application in China.

Once you grasp these basic concepts, the specifications and sizing recommendations that follow will be much easier to understand.
The scope of application of Type I steel grating is actually wider than many people think, from industrial platforms to municipal landscaping. The difference is that industrial settings focus more on load capacity and anti-corrosion, while municipal settings also consider appearance, theft prevention and pedestrian safety. Common practices for drainage trench covers in these scenarios can be viewed on the project cases page.
Key Advantages
Main features can be summarized as follows:
In use, steel grating mainly carries the weight of objects, so the main load-bearing members - the vertically arranged bearing flat bars - are checked for bending strength and stiffness as simply supported beams under uniform or concentrated loads. Therefore, the cross-section shape of bearing bars should meet the requirement that, with a given cross-sectional area, both strength and stiffness about the vertical bending axis are maximized, while lateral stability should also be good.
Overall, selection should weigh span, load and service environment together.
Clarifying the definition is mainly to avoid deviations in later communication. Type I steel grating may be named differently by different manufacturers and regions; when ordering, it is advisable to state the structure, material and surface treatment directly rather than only the name. Drainage trench covers also have such naming differences; attach drawings or photos in technical exchanges.
Specification Parameters of Steel Grating
Common specifications and corresponding parameters are summarized below; confirm each item before ordering:
Cross-section shape of I-type flat bars
The above are common specifications; actual ordered dimensions and tolerance requirements shall be confirmed against the layout drawing.
Actual parameters of the same model may differ slightly between manufacturers; acceptance should be based on measured values. Key dimensions of Type I steel grating should be spot-checked, especially for bulk deliveries. The corresponding parameters of drainage trench covers can be checked the same way; communicate promptly if deviations are found.
Basic Concepts of Steel Grating
Below we first briefly explain the relevant concepts and basic construction to make the following parameters and sizing content easier to understand.
The cross-section shapes of bearing flat bars currently used for steel grating are mainly rectangular-section bars with thickness T = 3, 4, 5, 6mm, and an I-type section bar that is thinner at the middle waist and thicker at both ends. The I-type section flat bar is a lightweight, economical section that saves metal. Together, rectangular and I-type section bars form the nominal thickness series of bearing bars for steel grating. The geometric and mechanical properties of the I-type section bar are much superior to the rectangular one: with equal bar height and cross-sectional area, the bending section modulus of an I-type bar is W = 0.200~0.203FH, while that of a rectangular bar is W = 0.167FH, so the I-type bar has much higher bending capacity. However, due to the shape characteristics and limitations of the I-type bar, not all rectangular bars can be replaced by equal-strength, equal-height I-type bars; the usable size range of I-type bars is also limited. The main reasons: when bar height is small, the end values of the I-type bar are too small, making it hard to hot-roll and unfavorable for recessed press welding; when bar height is large, the height-to-thickness ratio of the waist is too large, causing insufficient lateral stability. Therefore, the steel grating industry currently mainly uses rectangular section bars.

Once you grasp these basic concepts, the specifications and sizing recommendations that follow will be much easier to understand.
Bigger is not always better. Type I steel grating should be selected as economically as possible while meeting load requirements; excessive thickening increases weight and cost and complicates installation. The product page offers a more complete comparison of hot-dip galvanized trench covers for reference before deciding.
Features of Type I Steel Grating
Its overall performance focuses on the following aspects; we suggest comparing item by item in actual selection:
Using I-type section bars instead of rectangular section bars to produce steel grating can save 18% of steel weight. When the I-type and rectangular bars are identical in height, moment of inertia and bending section modulus, replacing the latter with the former reduces unit weight by about 18% while ensuring product quality - meaning the grating manufacturer gains about 18% more welded grating output for the same steel, increasing production efficiency and lowering project cost.

In recent years, international trade has raised new requirements for the steel used in welded steel grating, and replacing all rectangular section bars with I-type section bars conforms to this international trend. The Type I economical-section steel grating fully complies with the YB/T4001.1-2007 standard and can serve as an upgraded product: it increases output and economic benefits for manufacturers, and reduces weight and consumption for construction buyers.
Overall, selection should weigh span, load and service environment together.
Actual parameters of the same model may differ slightly between manufacturers; acceptance should be based on measured values. Key dimensions of Type I steel grating should be spot-checked, especially for bulk deliveries. The corresponding parameters of drainage trench covers can be checked the same way; communicate promptly if deviations are found.
Further notes: Common combinations of drainage trench covers and hot-dip galvanized trench covers
Besides what this article covers, drainage trench covers are also common in actual projects. It shares similarities with this article's subject in structure and fabrication; for selection, check span, load and service environment in the same order. If both types of components are used in the same project, we recommend unifying material and surface treatment to avoid later galvanic corrosion or inconsistent appearance.
- For all product specifications and theoretical weights by series, visit Steel Grating Product Center
- To estimate cost by size and quantity, use Instant Quote PageSubmit Requirements
- To see how similar projects were executed, refer to Project Cases field applications
FAQ
Can the values in the article be applied directly?
Values in this article come from relevant standard clauses or common industry practice. For actual selection, recalculate based on site span, load class and service environment; direct copying is not recommended.
What is most often overlooked during installation and acceptance?
First, bearing bars installed in the wrong direction reduce load capacity; second, insufficient fixing points or missing zinc touch-up paint; third, support beam spacing inconsistent with the layout drawing. These three items are most often overlooked on site.
What information is needed for custom sizes?
Usually you need to provide the panel dimensions (length x width), bearing bar specs and direction, center-to-center pitch of bearing bars and cross bars, surface treatment, and special requirements such as cutouts, corner notches and banding. Site photos or sketches are even better.
The above is for sizing and construction reference. To verify specific parameters or request a quotation, please visitInstant Quote Page, or contact our technical staff.
The above is general guidance. For a specific project, we still recommend submitting span, load class and service environment to our technicians for review. Steel grating is a load-bearing component; rework caused by wrong specification choices costs far more than the time spent on upfront calculation.






