
The core of selecting press-locked steel grating comes down to three things: span, load and environment. Span determines the series, load determines the bearing bar size and pitch, and environment determines the surface treatment. This page follows that order and explains how press-locked steel grating is commonly combined in real projects, so that after reading it you have a complete basis for judgement.
Items to Confirm When Selecting Press-Locked Steel Grating
This page does not list a fixed specification table, as such products are usually custom-fabricated to site conditions. We recommend confirming each item in the table above before inquiry: once mismatched with actual site conditions, refabrication is often required later.ProductsCommon specifications are organized by series for reference.
| Items to Confirm | What Needs to Be Clarified | Common Practices |
|---|---|---|
| Span and Support | Clear span between support beams and support surface width | Determine by field-measured dimensions |
| Service Load | Pedestrian, maintenance access or vehicle traffic | Verify by actual traffic type |
| Dimensions | Panel length and width, whether openings or notches are needed | Custom fabrication per layout drawing |
| End Treatment | Whether banding or end plates are needed | Banding recommended for open edges |
| Acceptance Requirements | Acceptance Criteria for Flatness, Tolerances and Appearance | Recommended to specify in the technical agreement |
| Packaging & Shipping | Whether packing and moisture protection are needed | Packing and cushioning recommended for long-distance shipping |
Press-Locked Steel Grating
The following points about press-locked steel grating are the ones most often asked about in purchasing and use, and the ones most worth confirming in advance:
Press-locked steel grating, also called insert grating, is manufactured from low-carbon flat bars, stainless steel, brass plate or aluminium plate of a certain size through slotting (punching), inserting, welding and finishing, forming aSteel Grating. The product has firm welds, uniform openings and an attractive design, and is convenient and practical. Press-locked steel grating has all the features of ordinary steel grating - high strength, corrosion resistance and maintenance-free - and adds uniform, precise assembly, a light and refined structure, natural harmony and elegant style. It is both a usable product and a work of art, and has found wide application.

The above points can serve as a pre-purchase checklist; confirm each item before moving to the quotation stage.
Press-Locked Steel Grating Types
Press-locked steel grating can be divided into the following categories by fabrication method and use; when selecting, determine the category first and then check the detailed parameters:
By different insertion methods and insertion angles, it can be divided into press-locked steel grating, heavy-duty steel grating, integral steel grating, sunshade steel grating, etc.
u Press-locked type press-locked steel grating: after the bearing flat bars are slotted, the cross flat bars are press-locked into shape. Generally, the maximum fabrication height for ordinary type steel grating is 100mm; the grating length is usually under 2000mm.
u Heavy-duty press-locked steel grating is a product where tall bearing bars and cross flat bars interlock and are pressed tight under 1200 tons of pressure. It is suitable for high-load, long-span applications.
u Integral type press-locked steel grating: the bearing bars and cross flat bars have the same height, with slot depth equal to 1/2 of the bearing bar. Grating height does not exceed 100mm; length is usually under 2000mm.
u Sunshade type press-locked steel grating: the bearing bars have 30° or 45° angled slots, and the cross bar flat bars are slotted and press-locked into shape. We can fabricate gratings with other pitches and specifications as needed, using ordinary carbon steel, stainless steel, aluminum and other materials. Grating height is under 100mm.
Determine the category first and then the specific model; this saves detours and makes comparison with other materials easier.
Press-Locked Steel Grating Specification Weight Table
Different specifications correspond to different load capacities and theoretical weights. Common specification parameters of press-locked steel grating are shown in the table below; the actual order dimensions and tolerances are subject to confirmation of the layout drawing:

Note: 1. Marking example: HG303/30 'HG"press-locked steel grating mark; "303" bearing bar section size [width x thickness] mm; "30" mesh opening pitch mm
2. The nominal width is calculated for a bearing bar thickness of 2mm; if the thickness is 5mm, add 3mm.
3. Besides the grid spacings in the table on this page, press-locked steel grating with other grid spacings can also be produced to user requirements.
The above are common specifications; actual ordered dimensions and tolerance requirements shall be confirmed against the layout drawing.
Press-Locked Steel Grating Selection Key Points
Confirm each item in the order below during selection to avoid most later rework. Record the conclusion of each step and submit it with your inquiry:
- Step 1 · Balance Appearance vs. Load Capacity: Press-locked panels have a neat appearance and uniform hole spacing, suitable for appearance-critical platforms; load capacity must be checked by series.
- Step 2 · Confirm Bearing Bar Specs and Pitch: Determined by span and load; the smaller the pitch, the denser the surface, with correspondingly higher self-weight and price.
- Step 3 · Confirm Whether Banding Is Needed: Open edges should be banded, both to protect the panel and to prevent edges lifting and injuring people.
- Step 4 · Confirm Installation and Maintenance Convenience: For areas needing frequent opening for maintenance, removable fixings rather than welding are recommended.
Once the above conditions are confirmed, proceed to Instant Quote PageEstimate quantities by dimensions, or send the condition list to customer service for model recommendations from our technicians.
Press-Locked Steel Grating Service Condition Comparison
The same specifications last very differently in different environments. The table below gives recommended practices by common service environment for your selection reference:
| Operating Environment | Recommended Practices | Note: |
|---|---|---|
| Indoor Dry Environments | Made of standard carbon steel with surface treatment as required | Focus on span and load; environmental impact is minimal |
| Outdoor and Open-Air Environments | Hot-dip galvanized surface treatment recommended | Check zinc coating integrity and re-zinc cut edges |
| Humid or Water Treatment Environments | Use a higher corrosion protection grade with matching fasteners | Regularly inspect fixing points and surface corrosion |
| High-Temperature or Large Temperature-Difference Environments | Select material and connection method by temperature | Watch for loosening caused by thermal expansion and contraction |
| Clean Rooms and Food & Pharmaceutical | Prioritize surface treatment and cleaning convenience | Avoid dust-collecting structures and cleaning dead corners |
| Temporary or Short-Term Use | Can be configured with the light-duty series | For short schedules, prioritize easy disassembly and turnover |
Custom Fabrication & Quotation
Before ordering, we recommend providing site photos, trench or platform dimensions and traffic requirements together, so we can give the model and layout plan in one go and reduce on-site cutting and rework. Common specifications are usually in stock; lead times for shaped parts and bulk orders depend on specification and quantity. For reference on similar projects, seeProject Cases; for a quotation, go directly to Instant Quote Page.
FAQ
What Are the Common Specifications of Press-Locked Steel Grating?
Common specifications are determined by combinations of bearing bar width and thickness, bearing bar pitch, and cross bar pitch; different combinations correspond to different load capacities and theoretical weights. Our Products section lists common models by series; you can also send span and load requirements to customer service for sizing help.
Which surface treatment should I choose?
Hot-dip galvanizing is recommended for outdoor or humid environments; for dry indoor environments, untreated or painted is fine; coastal, chemical and other strongly corrosive environments need thicker zinc coatings or stainless steel, depending on the expected service life.
Can it be custom-made to site dimensions?
Yes. Bearing bar specs, pitch, panel dimensions and banding forms can all be custom-made to drawings; cutouts, corner notches and shaped cutting are also supported. For bulk orders, a layout drawing can be confirmed before production.
Quotations can be given once the specifications and surface treatment of press-locked steel grating are confirmed. For custom fabrication to drawings or load calculations, you canInstant Quote PageSubmit dimensions, or contact us directly for technical support.






